Figures
Abstract
A study was conducted to assess the efficacy of ozone gas in inactivating spores of both Bacillus anthracis and Bacillus subtilis inoculated onto six building materials (glass, wood, carpet, laminate, galvanized metal, and wallboard paper). Testing conditions consisted of ozone gas concentrations ranging from 7,000–12,000 parts per million (ppm), contact times from 4 to 12 h, and two relative humidity (RH) levels of 75 and 85%. Results showed that increasing the ozone concentration, contact time, and RH generally increased decontamination efficacy. The materials in which the highest decontamination efficacy was achieved for B. anthracis spores were wallboard paper, carpet, and wood with ≥ 6 log10 reduction (LR) occurring with 9,800 ppm ozone, 85% RH, for 6 h. The laminate and galvanized metal materials were generally more difficult to decontaminate, requiring 12,000 ppm ozone, 85% RH, and 9–12 h contact time to achieve ≥6 LR of B. anthracis. Lastly, overall, there were no significant differences in decontamination efficacy between the two species.
Citation: Wood JP, Wendling M, Richter W, Rogers J (2020) The use of ozone gas for the inactivation of Bacillus anthracis and Bacillus subtilis spores on building materials. PLoS ONE 15(5): e0233291. https://doi.org/10.1371/journal.pone.0233291
Editor: Peter Setlow, University of Connecticut, UNITED STATES
Received: March 16, 2020; Accepted: May 2, 2020; Published: May 21, 2020
This is an open access article, free of all copyright, and may be freely reproduced, distributed, transmitted, modified, built upon, or otherwise used by anyone for any lawful purpose. The work is made available under the Creative Commons CC0 public domain dedication.
Data Availability: All of the reduced data are included in the paper and supporting information. More detailed data are available through US EPA’s science hub at https://catalog.data.gov/dataset/epa-sciencehub (DOI: 10.23719/1517612).
Funding: The US EPA funded Battelle Memorial Institute to perform this work via contract EP-C-10-001. Joseph Wood of the US EPA was the sponsor and technical director of the study, and was involved in the study design, data analysis, decision to publish, and preparation of manuscript.
Competing interests: The authors have declared no competing interests.
Introduction
The recently published 2018 National Biodefense Strategy calls for the U.S. to manage the risk of biological incidents and, specifically, conduct research and development of technologies to enhance preparedness to support decontamination. These biological threats can be categorized as naturally occurring, accidental, or deliberate attacks[1], such as the dissemination of virulent spores of Bacillus anthracis through the U.S. Postal Service[2]. Since this 2001 attack, a large body of research and development has been undertaken to evaluate decontamination techniques for this bioterrorism agent, and is reviewed here[3]. The present study builds on that research and supports the National Biodefense Strategy by verifying the efficacy of ozone gas as a decontaminant for inactivating B. anthracis spores deposited on various types of building materials.
The use of ozone gas for the inactivation of vegetative and spore-forming microorganisms on surfaces has been explored since at least 1982 [4]. More recently, ozone gas has been tested and is gaining traction for use in healthcare environments[5] for disinfection (in particular, inactivation of vegetative bacteria[6] and viruses[7]) and sterilization (inactivation of spore-forming microorganisms such as B. anthracis, Clostridioides difficile[8], and Bacillus cereus[6]). In addition, ozone gas has been approved for reprocessing (sterilization) of medical equipment that cannot be heat-treated [9]. The mechanism for the killing of spores by ozone is thought to be through damage to the inner membrane, thereby rendering the spores defective in germination[10]. The research described herein did not further investigate or confirm these mechanisms, but rather strived to elucidate the environmental and operational conditions necessary for inactivation of B. anthracis spores with ozone gas. Using ozone gas at relatively low concentrations (1–25 parts per million [ppm]), Akbas et al.[11] and Sharma et al. [6] demonstrated moderate efficacy (2–4 log10 reduction [LR]) against B. cereus and C. difficile spores on a number of different materials including figs, fabrics, and plastics. At approximately 5,000 ppm, 90% relative humidity (RH), and 22 °C for 4 h, Aydogan et al.[12] also reported only a moderate 2–4 LR (depending on the interior building material) in viable B. subtilis spore populations. An ozone concentration of 9,000 ppm ozone in air and a 1 h contact time were required to achieve > 6 LR of Bacillus atrophaeus (aka Bacillus globigii) spores on glass slides, with at least 70% RH and exposing spores to at least 70% RH levels for 15 h prior to exposure to ozone[13]. Mahfoudh et al. [14] discuss the role that elevated RH plays in fumigation with ozone and other gaseous decontaminants, via the swelling of spores and creating “channels” for gas to diffuse into the spore. Other research groups [12, 15, 16] have corroborated the finding that increasing RH levels (> 80%) improves efficacy with ozone gas. Indeed, a higher RH during fumigation with other gases[3] or with hot air [17–20] is usually associated with improved decontamination efficacy for B. anthracis spores.
While the literature mentioned above contributes to the science and engineering of using ozone gas as a sporicide, there are few data available showing ozone fumigation conditions required for achieving ≥ 6 LR of a spore population. The “6 LR” benchmark originates from efficacy testing guidance for antimicrobial chemicals with claims to inactivate spores of B. anthracis on surfaces[21]. Additionally, there is a paucity of data for the use of ozone gas in the inactivation of B. anthracis spores on surfaces. In a short conference proceeding, Buranov et al.[22] indicated that 20 mg/L (~ 10,000 ppm) ozone for 1 h was sufficient for complete inactivation of 106 and 108 spores of a B. anthracis vaccine strain deposited on an empty Petri plate; however, minimal data and details on the methods used were provided.
The present study fills these research gaps by presenting data for the first time verifying the conditions necessary (required ozone gas concentrations, RH levels) for effective inactivation (i.e., ≥ 6 LR) of virulent B. anthracis (Ames strain) spores using ozone gas. In addition, decontamination efficacy data are presented for the first time for both B. subtilis and B. anthracis tested under the same conditions to allow comparison of the resistance to ozone gas for the two species and verify use of B. subtilis as a potential surrogate for B. anthracis when conducting decontamination tests with ozone gas. B. subtilis was chosen for comparison with B. anthracis, consistent with its demonstration as a suitable surrogate in previous other decontamination studies[23–26]. Although we do acknowledge that the use of Bacillus thuringiensis as a surrogate for B. anthracis in decontamination studies is becoming more widely used [17–19, 27]. Lastly, the present study is novel for evaluating decontamination efficacy with B. anthracis spores inoculated on common realistic interior and exterior building materials. Many biological decontamination studies tend to use only one or two basic laboratory substrates such as glass or Petri plates and overlook the typically significant effect that material has on efficacy.
Materials and methods
Microorganisms
Testing was conducted with B. anthracis (Ames strain) spores produced at Battelle Biomedical Research Center in West Jefferson, OH, and verified via genotyping. The virulent Ames strain used in this study was the strain used in the 2001 B. anthracis letter attacks.[28] All portions of this testing were performed under Biosafety Level 3 conditions, in accordance with the Federal Select Agent Program (FSAP) regulations set forth by the Centers for Disease Control and Prevention.
Testing was also conducted with B. subtilis spores (ATCC 19659) from a stock culture. Details of the methods used to produce spores of both species are published elsewhere in several previous articles[24, 26, 29, 30]. Briefly, the B. anthracis spores were prepared using a BioFlo 3000 fermentor (New Brunswick Scientific Co., Inc., Edison, NJ, USA). A culture was grown for 16–18 h at 37 °C in nutrient broth (BD Diagnostic Systems, Sparks, MD, USA), and was then used to inoculate Leighton-Doi Broth (BD Diagnostic Systems) in the fermentor. Cultures were grown in the fermentor for 24 h at 37 °C. Cultures exhibiting >80% refractile spores via phase-contrast microscopy were centrifuged at 11,000 g for 15–20 min at 2–8 °C. The resultant pellet was washed twice and resuspended in ice-cold sterile water to further remove cellular debris. To inactivate any vegetative cells, the suspension was then heat-shocked by incubating at 60 °C for 45–60 min, then centrifuged and washed again. Final preparation involved centrifuging the sample through a gradient of ice-cold, sterile 58% Hypaque-76 (Nycomed Amersham, Princeton, NJ, USA) at 9,000 g for 2 h at 2–8 °C. This batch of spores was used throughout the study. B. subtilis stock suspensions were prepared in a manner similar to the above procedures for B. anthracis and as previously described [31]. The resultant B. anthracis and B. subtilis spore preparations having >95% refractile spores with <5% cellular debris were enumerated, diluted in sterile water to a target of 109 colony-forming units (CFU) per mL, and stored at 2–8 °C. Spores were also tested to ensure HCl resistance for 2 min. No specific tests were performed to check for germination while the spores were stored at 2–8 °C, however a check on the titer of the spore lot was performed at the start of each test. This was to ensure that the titer of the stock was not changing, providing an indication that no germination was happening.
Coupon experimental materials
Decontamination testing was conducted using realistic building exterior and interior materials. These materials included glass, wood, carpet, laminate, galvanized metal, and painted wallboard paper. Information on the materials and associated sterilization approaches is presented in Table 1. Coupons of the materials were cut to 1.9 cm width by 7.5 cm length from larger pieces. Coupons were then sterilized by autoclaving or gamma irradiation (at ~40 kilogray), depending on cost and compatibility with materials.
Inoculation, recovery, and quantification of microorganisms
Each of the test and positive control coupons was inoculated with a target of 1 x 108 CFU of either B. anthracis or B. subtilis spores. (The spore suspension titer was verified each day of testing.) A 100-μL aliquot of a stock suspension of approximately 1 x 109 CFU/mL, dispensed using a micropipette, was applied as 10 μL droplets across the coupon surface. After inoculation, the coupons were placed in a biosafety cabinet (BSC) to allow the suspension to dry overnight, under laboratory ambient conditions of approximately 22 °C and 40% RH. The number and type of replicate coupons used for each combination of microorganism, material, and test condition (ozone concentration, RH, and contact time) were as follows:
- 5 replicate test coupons (inoculated with B. anthracis or B. subtilis spores and exposed to ozone)
- 5 positive controls (inoculated with B. anthracis or B. subtilis spores, but not exposed to ozone)
- 1 laboratory blank (inoculated only with sterile water and not exposed to ozone)
- 1 procedural blank (inoculated only with sterile water and exposed to ozone for the longest contact time).
Following each test, spores were extracted from each coupon as follows: Each coupon (test coupons, positive controls, and blanks) was placed in a 50-mL polypropylene conical vial containing 10 mL of sterile phosphate-buffered saline extraction buffer containing 0.1% Triton X-100 surfactant (Sigma, St. Louis, MO, USA). The vials were capped, placed on their side and agitated on an orbital shaker for 15 minutes at approximately 200 revolutions per minute (rpm) at room temperature. Spores were then quantified from this extraction suspension using standard dilution plating techniques. Briefly, the extract was removed, and a series of 10-fold dilutions was prepared in sterile water. An aliquot (0.1 mL) of either the undiluted extract and/or each serial dilution was plated onto tryptic soy agar in triplicate. The cultures were incubated for 18–24 h at 37 °C ± 2 °C for B. anthracis and 35 °C ± 2 °C for B. subtilis. Colonies were counted manually, and the CFU/mL value was determined by multiplying the average number of colonies per plate by the reciprocal of the dilution. Dilution data representing the greatest number of individually definable colonies (within a range of 25–250 discernible colonies per plate) were expressed as arithmetic mean ± standard deviation of the numbers of CFU observed. The CFU recovered from each coupon were determined by multiplying the CFU/mL by 10 (as 10 mL was used to extract each coupon).
Ozone gas concentration, temperature, and RH production and measurement
Ozone gas exposure testing was conducted inside a Class III Biological Safety cabinet (The Baker Company, Sanford, ME, USA) (0.57 m3). Ozone gas used in the test chamber was produced with a commercially-available generator (AC-2045, IN USA Inc., Norwood, MA, USA), which used 99.5% oxygen as its feedstock. The generator was run at 100% power until the target concentration in the test chamber was reached, and subsequently reduced to approximately 30% power to maintain concentration. Ozone gas concentrations < 10,000 ppm or > 10,000 ppm were measured with a low (IN-2000-L2-LC, IN USA Inc., Needham, MA, USA) or high (Mini Hicon-LR, IN USA Inc.) concentration gas analyzer, respectively. Both ozone gas analyzers were calibrated by the manufacturer prior to shipment. Ozone concentrations were logged automatically every minute using a HOBO data logger (Onset Computer Corporation, Bourne, MA, USA).
A custom-made ultrasonic fogger was used to raise humidity inside the test chamber. Air saturated with moisture from the fogger was injected into the chamber via polyvinyl chloride tubing until the target RH was reached. Additional humidified air was injected into the chamber as needed to maintain target RH levels. In initial method development tests, an off-the-shelf hygrometer was used to measure RH, but the hygrometer became readily damaged upon exposure to ozone gas. Hence, a wet/dry bulb hygrometer was custom-fabricated using two National Institute of Standards and Technology [NIST]-traceable thermometers [Fisher 13-990-270]) and used to monitor the temperature and RH inside the test chamber. For the wet bulb thermometer, a wicking material was wrapped around one thermometer bulb, and the wick was kept wet by immersion in a small reservoir of water. The other thermometer provided the dry temperature reading. A small fan (Cooler Guys, UF12BWL, Kirkland, WA, USA) provided constant air flow for the thermometers and for mixing inside the chamber. Differences in the dry and wet bulb temperature readings (taken and manually recorded every 2–15 minutes) were used to determine RH, using an online humidity calculator [32].
For each experiment (one ozone concentration and RH level), coupons inoculated with B. anthracis or B. subtilis spores were placed in sealed containers (Lock & Lock, HPL838P, Farmers Branch, TX, USA) and then placed into the test chamber. All containers were open until the target RH was achieved. Then, all containers were closed during the initial injection of ozone. The containers holding the test coupons were then opened sequentially to achieve an appropriate contact time for exposure to ozone. Contact time was defined as the time from opening the container to the time ozone was exhausted from the chamber. Positive controls and laboratory blanks were also kept in sealed containers for the full fumigation cycle. The procedural blank coupons were opened for exposure to ozone at the same time as the test coupons with the longest contact time (e.g., 8 or 12 h). At the end of the fumigation cycle, the ozone generator was shut down and the ozone rapidly exhausted until the ozone analyzer read zero. All test coupons were subsequently removed from the BSC III and processed for remaining viable spores.
Test matrix and ozone fumigation procedures
The overall test matrix for the study is shown in Table 2. Test variables for the study included microorganism, building material, ozone concentration, contact time, and RH level. Ozone concentrations ranged from 7,000–12,000 ppm. Tests for each microorganism (B. subtilis, B. anthracis Ames) were conducted separately but under the same conditions, and all six materials were used in every experiment. Three contact times were evaluated for each of the seven fumigation conditions (ozone concentration and RH level). At the 9,000-ppm concentration, the 85% RH condition was tested twice to evaluate longer ozone exposure times. At the lower concentrations of 7,000 and 9,000 ppm ozone, efficacy at both 75 and 85% RH was evaluated to assess the effect of RH. To ensure demonstration of effective decontamination for all materials, the remaining experiments were designed to focus on higher ozone concentrations at 85% RH for contact times out to 12 h.
Calculation of spore recovery and decontamination efficacy
The methods we used for determining spore recovery and decontamination efficacy are described elsewhere.[30] Briefly, the average percent spore recovery from each set of positive controls for a given material was calculated for each test and microorganism using the following equation:
(1)
where Mean CFUpc is the mean number of CFU recovered from the five replicate positive control (pc) coupons for a given material, and CFUspike is the number of CFU spiked (inoculated) onto each of those coupons, determined via analysis of the inoculum each day of testing.
Decontamination efficacy was calculated in terms of LR for each material, microbe, and test condition. For each test (noted with subscript t) and positive control coupon, the number of CFU recovered after each test was transformed to its log10 value. Then, the mean of the log10 values for each test coupon (five replicates) was subtracted from the mean of the log10 values from each positive control (five replicates), as follows:
(2)
Test coupons in which there were no CFU recovered were assigned a CFU count of 1, resulting in a log10 CFU of zero. In such cases, the LR is reported as ≥ the value calculated by Eq 2.
The LR results are each reported with an associated 95% confidence interval (CI), calculated as follows:
(3)
The term SE is the pooled standard error, and was calculated as follows:
(4)
where S is the standard deviation of the LR results for either the five positive controls (pcs) or five test coupons (t) for each combination of decontaminant, coupon material, and microorganism tested.
Statistical analyses
A multilevel model was performed that included microorganism, material, RH, and ozone dosage (ozone concentration × exposure time) as predictors of efficacy. To account for the nonlinearity observed in the response, ozone concentration and exposure time were additionally included in the model as factors. Validity conditions were assessed using diagnostic plots and/or statistical tests (where appropriate) to assist in justifying the approach taken. When fitting a multilevel model, it is assumed that there is a linear relationship between the predictors and the response, the random errors are homogeneous, the errors are uncorrelated, and the error terms are normally distributed. F-tests were performed on the model to help address the questions of interest for main effects and interactions investigating if there are any differences, statistically, between levels or values of predictors. We then performed t-tests on the model to explore in more depth how the response differs across levels or values of predictors. There were interactions present among the predictors, and we determined how the response differs across levels or whether the values of one predictor are conditional on other predictors. All statistical analyses were performed in R (https://www.r-project.org/).
In addition to the statistical analysis, a simple ranking approach was sometimes used to distinguish the effect of test variables (such as material, RH) on efficacy, i.e., some results were ranked or described in terms of the number of occurrences in which the decontamination was effective. We consider a decontamination result “effective” if the efficacy is ≥ 6 LR, which is a benchmark based on guidance provided for the evaluation of antimicrobial products with claims to inactivate B. anthracis spores on surfaces [21]. Another criterion used to rank efficacy results was based on whether the decontamination treatment or test condition resulted in no spores recovered from all five replicate test coupons following decontamination; this condition is sometimes referred to as complete inactivation or complete decontamination.
Results and discussion
Fumigation conditions
Actual fumigation conditions, in terms of the average temperature, RH, and ozone concentration for each experiment, did not deviate significantly from the target conditions. That is, with a target temperature of 25 °C for all tests, actual average temperatures ranged from 24.2–26.0 °C. For RH, actual levels typically did not deviate more than two percentage points from the target levels of either 75 or 85%. For ozone concentration, average actual levels deviated no more than 28 ppm from the targets. The actual fumigation conditions for each experiment are summarized in Tables 3 and 4.
Inoculation and recovery of spores from positive controls
For the overall study, the average (± SD) number of B. anthracis spores inoculated onto each coupon in each trial was 8.01 ± 0.08 log CFU and for B. subtilis, the number of spores was 8.05 ± 0.21 log CFU. The average percent recovery for each microorganism from the positive controls is tabulated in Table 5 for each material type. The mean percent recovery from positive controls was higher for the B. anthracis compared to B. subtilis, for five of the six materials, although the estimated differences in percent recovery were relatively minor. Overall, the average percent spore recoveries ranged from 3%-77%. The lowest percent recoveries for both species were obtained for wood positive controls and averaged less than 10%. Nevertheless, recoveries for both species from wood positive controls were always greater than 6 log CFU, allowing the decontamination condition to demonstrate ≥ 6 LR. For B. subtilis, the highest recoveries were obtained for galvanized metal, and for B. anthracis, highest recoveries were obtained with carpet. These results for percent recovery of spores from the positive control materials are similar and consistent with other decontamination studies using spores of B. anthracis and B. subtilis [26, 33].
Decontamination efficacy of ozone gas
Overview/effect of concentration.
The decontamination efficacy results, in terms of average LR, are summarized in Tables 6 and 7 for B. anthracis spores and B. subtilis spores, respectively (Also refer to the Supporting Information S1 File, S1-S14 Figs in S1 File, for a graphical representation of the data). The tabulated results are shown by ozone fumigation condition (i.e., concentration and RH level), contact time, and material. Overall, decontamination efficacy was evaluated for 252 cases (six materials × seven fumigation conditions × three contact times × two microorganism species). Ozone gas target concentrations ranged from 7,000 to 12,000 ppm, coupled with contact times ranging from 4–12 h.
Overall, efficacy ranged from a low of 0.39 LR (Test 2, with galvanized metal ductwork, B. subtilis, 7000 ppm, 4 h, 75% RH) to complete inactivation (≥7.9 LR in some cases, depending on the positive control recovery). The LR results shown in bold in Tables 6 and 7 signify a test condition and material that resulted in complete inactivation, i.e., there were no spores recovered from any of the five replicate test coupons. There were several conditions (>50) in which this occurred, and complete inactivation tended to happen more frequently at the higher RH, at higher ozone concentrations, and longer contact times, as expected, although we caveat that there were several ozone fumigation conditions in which increasing contact time offered no increase in efficacy; see, for example, the tests at 7,000 and 9,000 ppm, at the lower 75% RH level, for both species. At the most robust decontamination condition of 12,000 ppm ozone and 85% RH, all but four (out of 18) test material/contact time combinations resulted in effective decontamination (≥ 6 LR) for B. anthracis.
There are few data from the literature with which to compare our efficacy results due to differences in test methodology, microorganisms, test materials, and ozone fumigation conditions. Nevertheless, we report the literature that may be somewhat relevant or comparable to our tests. For example, Aydogan and Gurol [12] showed improvement in efficacy against B. subtilis spores with increasing contact time, ozone concentration, and RH (consistent with our study), although their testing utilized a maximum ozone concentration of approximately 5,000 ppm and a maximum contact time of only four h, and never demonstrated efficacy ≥ 4 LR.
Only a few studies in the literature report ozone gas achieving ≥ 6 LR of bacterial spores except when using relatively high concentrations, consistent with our findings. As an example, Buranov et al.[22] in a conference proceeding reported that decontamination efficacy > 6 LR with an avirulent strain of B. anthracis was achieved with ozone concentrations of ~ 10,000 ppm, consistent with the present study. Currier et al.[13] demonstrated ≥ 6 LR against spores of B. globigii on glass coupons when using 9,000 ppm ozone with only a 1 h contact time. These results are comparable to our testing, in which ≥ 6 LR was achieved for B. subtilis on glass at 9,000 ppm, 75% RH; however, an 8 h contact time was needed. The demonstration of effective decontamination only after 1 h by Currier et al.11 may be due to the spores being preconditioned by exposure to elevated RH levels for 15 h prior to fumigation with ozone. In contrast, Sharma et al.[6] tested ozone gas at a low level of 25 ppm against spores of C. difficile and B. cereus, but the populations of these bacteria were insufficiently high (up to a maximum of 4 log CFU) to demonstrate ≥ 6 LR.
Effect of material.
Six materials were included in the present study to assess their effect on decontamination efficacy and included both porous (carpet, wood) and nonporous (glass, laminate, galvanized metal, and wallboard paper) materials. Overall, ozone gas was effective in inactivating B. anthracis spores on all materials under at least one test condition, and for B. subtilis, ozone gas was effective under at least one test condition for all materials except wood. For some materials, such as wood, carpet, and wallboard paper, effective decontamination was achieved for B. anthracis with the lowest ozone concentration tested (7,000 ppm), while materials such as laminate and metal ductwork required 12,000 ppm to achieve ≥ 6 LR of B. anthracis. Further, the effect of material on efficacy varied by the species. For example, in terms of the number of successful decontamination events (≥ 6 LR) or lack thereof, spores of B. anthracis were the most difficult to inactivate when associated with the laminate, metal ductwork, and glass materials, while B. subtilis was more difficult to inactivate when associated with wood and carpet. It is possible that this difference may be attributed to structural or molecular differences between the two species. For instance, the spore outer coat is comprised of different proteins for both species, and B. anthracis spores possess an exposporium, whereas B. subtilis spores do not.[25] For both species, the painted wallboard paper material was effectively decontaminated the most frequently (62% of the tests for B. anthracis, and 81% of the tests for B. subtilis) compared to the other materials. Painted wallboard paper and other organic materials (carpet, wood) perhaps generate reactive oxygen species (ROS) upon exposure (and reaction) to ozone gas, which may explain why efficacy is higher for these materials (further discussed below).
The Aydogan and Gurol study[12] was the only study we found that used somewhat comparable test materials and demonstrated that wood and carpet were more difficult to decontaminate compared to materials such as glass and floor tile. This finding is consistent with our observations relative to the effect of material on ozone gas efficacy for inactivation of B. subtilis. However, for B. anthracis, we found that effective ozone decontamination occurred more often on wood and carpet compared to glass, laminate and metal ductwork. It is unclear why this difference in results between the two species occurred. Generally, inorganic, nonporous materials such as glass, laminate, or galvanized metal are typically easier to effectively decontaminate compared to porous and organic materials such as carpet and wood, especially when using oxidation-based sporicides such as ozone.[3] The observation that B. anthracis spores were relatively more difficult to inactivate with ozone gas on glass, galvanized metal and laminate indicates the possibility of a different inactivation mechanism involved. Ozone gas is known to react with organic matter to produce ROS (which may include hydroxyl and peroxyl radicals, and peroxides[34–36]), and these ROS may be sporicidal themselves. Ozone gas itself is considered an ROS; ROS generated from non-thermal plasmas have been shown to be sporicidal[37]. Further research is recommended to better elucidate the potential different inactivation mechanisms for the two species.
Effect of RH.
In the tests in which the lower RH of 75% was utilized (Tests 1 and 3), there were only two occurrences (out of 72, or ~3%) in which effective decontamination was achieved (B. subtilis; wallboard paper and glass; at 9,000 ppm). In contrast, for Tests 2 and 4, which were conducted under the same conditions as Tests 1 and 3 except at the higher RH of 85%, 32% of the results demonstrated effective decontamination (Refer to the Supporting Information for a graphical representation of the data). In these graphs, we can observe that the inactivation efficacy for B. anthracis was higher at 85% RH than at 75% for most of the comparisons, but the difference in efficacy for the two RH levels was less pronounced on the glass and metal materials. The general result showing improved efficacy with increased RH is consistent with other studies[12, 14–16]. Comparable to our findings, Ishizaki et al.[16] demonstrated an approximately 3 log improvement in the inactivation of B. cereus and B. subtilis spores on filter paper when RH was increased from 70 to 80%. The statistical model also confirms that there is strong evidence that RH does affect decontamination efficacy, with a p-value < 0.0001.
Effect of species.
As discussed above, the effect of microorganisms on decontamination efficacy with ozone gas varied somewhat by the material onto which the spore population was deposited. Overall, out of the 126 test conditions for each species (six materials × three contact times × seven fumigation conditions), there were 53 occurrences in which decontamination was effective against B. anthracis, and 45 occurrences in which decontamination was effective against B. subtilis. This global comparison of the two species indicates that B. subtilis may be slightly more resistant to ozone gas inactivation compared to B. anthracis. Overall, the results from the statistical analysis indicate there was no significant difference between the two species, with a p-value of 0.32. But when accounting for material interactions in the model, the species does have a significant effect (p <0.0001). This observed similarity or increase in resistance of B. subtilis to ozone gas as compared to B. anthracis is consistent with the literature in which the resistance of B. subtilis or B. atrophaeus is comparable to B. anthracis with the use of several other decontaminants[3]. We believe our study is the first to make the direct comparison between the two species relative to their resistance to ozone gas inactivation and supports the use of B. subtilis as a surrogate for B. anthracis for this decontaminant. Further research is recommended to demonstrate the ozone gas decontamination technology at a larger scale.
Supporting information
S1 File. Decontamination efficacy results plotted by microorganism, material, and by ozone gas fumigation condition.
https://doi.org/10.1371/journal.pone.0233291.s001
(DOCX)
Acknowledgments
Disclaimer: The EPA, through its Office of Research and Development, directed the research described herein. It has been subjected to the Agency’s review and has been approved for publication. Mention of trade names, products or services does not convey official EPA approval, endorsement or recommendation.
References
- 1.
U.S. Department of Defense, U.S. Department of Health and Human Services, U.S. Department of Homeland Security, U.S. Department of Agriculture. National Biodefense Strategy. 2018.
- 2. Canter DA. Remediating anthrax-contaminated sites: Learning from the past to protect the future. Chem Health Safey. 2005;12:13–9.
- 3. Wood JP, Adrion AC. Review of Decontamination Techniques for the Inactivation of Bacillus anthracis and Other Spore-Forming Bacteria Associated with Building or Outdoor Materials. Environ Sci Technol. 2019;53(8):4045–62. pmid:30901213
- 4. Masaoka T, Kubota Y, Namiuchi S, Takubo T, Ueda T, Shibata H, et al. Ozone decontamination of bioclean rooms. Appl Environ Microbiol. 1982;43(3):509–13. pmid:6803668
- 5. Sousa CS, Torres LM, Azevedo MP, de Camargo TC, Graziano KU, Lacerda RA, et al. [Sterilization with ozone in health care: an integrative literature review]. Rev Esc Enferm USP. 2011;45(5):1243–9. pmid:22031389.
- 6. Sharma M, Hudson JB. Ozone gas is an effective and practical antibacterial agent. Am J Infect Control. 2008;36(8):559–63. pmid:18926308
- 7. Hudson J, Sharma M, Petric M. Inactivation of Norovirus by ozone gas in conditions relevant to healthcare. J Hosp Infect. 2007;66(1):40–5. pmid:17350729
- 8. Davies A, Pottage T, Bennett A, Walker J. Gaseous and air decontamination technologies for Clostridium difficile in the healthcare environment. J Hosp Infect. 2011;77(3):199–203. pmid:21130521
- 9.
U.S. Food and Drug Administration. Reprocessing Medical Devices in Health Care Settings: Validation Methods and Labeling Guidance for Industry and Food and Drug Administration Staff. Rockville, MD2015.
- 10. Young SB, Setlow P. Mechanisms of Bacillus subtilis spore resistance to and killing by aqueous ozone. J Appl Microbiol. 2004;96(5):1133–42. pmid:15078531
- 11. Akbas MY, Ozdemir M. Application of gaseous ozone to control populations of Escherichia coli, Bacillus cereus and Bacillus cereus spores in dried figs. Food Microbiol. 2008;25(2):386–91. http://dx.doi.org/10.1016/j.fm.2007.09.007. 19804048; 8091458. pmid:18206781
- 12. Aydogan A, Gurol MD. Application of gaseous ozone for inactivation of Bacillus subtilis spores. J Air Waste Manage Assoc. 2006;56(2):179–85.
- 13. Currier R, Torraco D, Cross J, Wagner G, Gladden P, Vanderberg L. Deactivation of clumped and dirty spores of Bacillus globigii. Ozone Sci Eng. 2001;23(4):285–94.
- 14. Mahfoudh A, Moisan M, Seguin J, Barbeau J, Kabouzi Y, Keroack D. Inactivation of vegetative and sporulated bacteria by dry gaseous ozone. Ozone: Science & Engineering. 2010;32(3):180–98.
- 15. Menetrez M, Foarde K, Schwartz T, Dean T, Betancourt D. An Evaluation of the Antimicrobial Effects of Gas-Phase Ozone. Ozone: Science & Engineering. 2009;31(4):316–25.
- 16. Ishizaki K, Shinriki N, Matsuyama H. INACTIVATION OF BACILLUS SPORES BY GASEOUS OZONE. J Appl Bacteriol. 1986;60(1):67–72. pmid:3082844
- 17. Buhr TL, Young AA, Barnette HK, Minter ZA, Kennihan NL, Johnson CA, et al. Test methods and response surface models for hot, humid air decontamination of materials contaminated with dirty spores of Bacillus anthracis Sterne and Bacillus thuringiensis Al Hakam. J Appl Microbiol. 2015;119(5):1263–77. Epub 2015/08/11. pmid:26258399.
- 18. Buhr TL, Young AA, Bensman M, Minter ZA, Kennihan NL, Johnson CA, et al. Hot, humid air decontamination of a C‐130 aircraft contaminated with spores of two acrystalliferous Bacillus thuringiensis strains, surrogates for Bacillus anthracis. J Appl Microbiol. 2016;120(4):1074–84. pmid:26786717
- 19. Buhr TL, Young AA, Minter ZA, Wells CM, McPherson DC, Hooban CL, et al. Test method development to evaluate hot, humid air decontamination of materials contaminated with Bacillus anthracis Sterne and B. thuringiensis Al Hakam spores. J Appl Microbiol. 2012;113(5):1037–51. Epub 2012/08/18. pmid:22897143.
- 20. Setlow B, Parish S, Zhang P, Li YQ, Neely WC, Setlow P. Mechanism of killing of spores of Bacillus anthracis in a high-temperature gas environment, and analysis of DNA damage generated by various decontamination treatments of spores of Bacillus anthracis, Bacillus subtilis and Bacillus thuringiensis. J Appl Microbiol. 2014;116(4):805–14. http://dx.doi.org/10.1111/jam.12421 pmid:24344920. 1508678987.
- 21.
U.S. Environmental Protection Agency. Product Performance Test Guidelines OCSPP 810.2100: Sterilants, Sporicides, and Decontaminants, Guidance for Efficacy Testing. EPA 712-C-17-003. Washington, D.C.: 2018 EPA 712-C-17-003 Contract No.: EPA 712-C-17-003.
- 22.
Buranov S, Karelin V, Selemir V, Vorobieva O, Tsareva A, Shkarin V, editors. Sterilizing Effect of Ozone on Live Spores of Anthrax Bacillus. Pulsed Power Conference, 2005 IEEE; 2005: IEEE.
- 23. Rogers JV, Choi YW, Richter WR, Rudnicki DC, Joseph DW, Sabourin CL, et al. Formaldehyde gas inactivation of Bacillus anthracis, Bacillus subtilis, and Geobacillus stearothermophilus spores on indoor surface materials. J Appl Microbiol. 2007;103(4):1104–12. Epub 2007/09/28. pmid:17897215.
- 24. Rogers JV, Sabourin CL, Choi YW, Richter WR, Rudnicki DC, Riggs KB, et al. Decontamination assessment of Bacillus anthracis, Bacillus subtilis, and Geobacillus stearothermophilus spores on indoor surfaces using a hydrogen peroxide gas generator. J Appl Microbiol. 2005;99(4):739–48. Epub 2005/09/16. pmid:16162224.
- 25. Sagripanti JL, Carrera M, Insalaco J, Ziemski M, Rogers J, Zandomeni R. Virulent spores of Bacillus anthracis and other Bacillus species deposited on solid surfaces have similar sensitivity to chemical decontaminants. J Appl Microbiol. 2007;102(1):11–21. Epub 2006/12/23. pmid:17184315.
- 26. Wood JP, Choi YW, Rogers JV, Kelly TJ, Riggs KB, Willenberg ZJ. Efficacy of liquid spray decontaminants for inactivation of Bacillus anthracis spores on building and outdoor materials. J Appl Microbiol. 2011;110(5):1262–73. Epub 2011/02/22. pmid:21332900.
- 27. Buhr TL, Wells CM, Young AA, Minter ZA, Johnson CA, Payne AN, et al. Decontamination of materials contaminated with Bacillus anthracis and Bacillus thuringiensis Al Hakam spores using PES-Solid, a solid source of peracetic acid. J Appl Microbiol. 2013;115(2):398–408. Epub 2013/05/23. pmid:23692445.
- 28. Van Ert MN, Easterday WR, Simonson TS, U’Ren JM, Pearson T, Kenefic LJ, et al. Strain-specific single-nucleotide polymorphism assays for the Bacillus anthracis Ames strain. J Clin Microbiol. 2007;45(1):47–53. pmid:17093023
- 29. Wood JP, Meyer KM, Kelly TJ, Choi YW, Rogers JV, Riggs KB, et al. Environmental persistence of Bacillus anthracis and Bacillus subtilis spores. PLoS One. 2015;10(9):e0138083. pmid:26372011
- 30. Wood JP, Wendling M, Richter W, Lastivka A, Mickelsen L. Evaluation of the Efficacy of Methyl Bromide in the Decontamination of Building and Interior Materials Contaminated with Bacillus anthracis Spores. Appl Environ Microbiol. 2016;82(7):2003–11. pmid:26801580
- 31. Rogers JV, Richter WR, Choi YW, Judd AK. Use of superabsorbent polymer gels for surface decontamination of Bacillus anthracis spores. Lett Appl Microbiol. 2009;48(2):180–6. Epub 2008/12/06. pmid:19055629.
- 32.
calculator Rh. Available from: http://www.ringbell.co.uk/info/humid.htm.
- 33. Richter WR, Wood JP, Wendling MQ, Rogers JV. Inactivation of Bacillus anthracis spores to decontaminate subway railcar and related materials via the fogging of peracetic acid and hydrogen peroxide sporicidal liquids. J Environ Manage. 2018;206:800–6. pmid:29174643
- 34. Chen X, Hopke PK, Carter WP. Secondary organic aerosol from ozonolysis of biogenic volatile organic compounds: chamber studies of particle and reactive oxygen species formation. Environ Sci Technol. 2010;45(1):276–82. pmid:21121662
- 35. Khurshid S, Siegel J, Kinney K. Particulate reactive oxygen species on total suspended particles–measurements in residences in Austin, Texas. Indoor Air. 2016;26(6):953–63. pmid:26588044
- 36. Venkatachari P, Hopke PK. Characterization of products formed in the reaction of ozone with α-pinene: case for organic peroxides. J Environ Monit. 2008;10(8):966–74. pmid:18688467
- 37. Uhm HS, Choi EH, Cho GS, Hwang DH. Influence of reactive oxygen species on the sterilization of microbes. Current Applied Physics. 2013;13:S30–S5.