PONE-D-21-16599

Research on rapier loom fault system based on cloud-side collaboration

PLOS ONE

Dear Dr. Wan,

Thank you for submitting your manuscript to PLOS ONE. After careful consideration, we feel that it has merit but does not fully meet PLOS ONE’s publication criteria as it currently stands. Therefore, we invite you to submit a revised version of the manuscript that addresses the points raised during the review process.

ACADEMIC EDITOR:

Based on the comments received from the reviewers and my own observation, I recommend major revisions for the article.

Please submit your revised manuscript by Aug 01 2021 11:59PM. If you will need more time than this to complete your revisions, please reply to this message or contact the journal office at plosone@plos.org. When you're ready to submit your revision, log on to https://www.editorialmanager.com/pone/ and select the 'Submissions Needing Revision' folder to locate your manuscript file.

Please include the following items when submitting your revised manuscript:

• A rebuttal letter that responds to each point raised by the academic editor and reviewer(s). You should upload this letter as a separate file labeled 'Response to Reviewers'.
• A marked-up copy of your manuscript that highlights changes made to the original version. You should upload this as a separate file labeled 'Revised Manuscript with Track Changes'.
• An unmarked version of your revised paper without tracked changes. You should upload this as a separate file labeled 'Manuscript'.

If you would like to make changes to your financial disclosure, please include your updated statement in your cover letter. Guidelines for resubmitting your figure files are available below the reviewer comments at the end of this letter.

If applicable, we recommend that you deposit your laboratory protocols in protocols.io to enhance the reproducibility of your results. Protocols.io assigns your protocol its own identifier (DOI) so that it can be cited independently in the future. For instructions see: http://journals.plos.org/plosone/s/submission-guidelines#loc-laboratory-protocols. Additionally, PLOS ONE offers an option for publishing peer-reviewed Lab Protocol articles, which describe protocols hosted on protocols.io. Read more information on sharing protocols at https://plos.org/protocols?utm_medium=editorial-email&utm_source=authorletters&utm_campaign=protocols.

We look forward to receiving your revised manuscript.

Kind regards,

Thippa Reddy Gadekallu

Academic Editor

PLOS ONE

Journal Requirements:

When submitting your revision, we need you to address these additional requirements.

1. Please ensure that your manuscript meets PLOS ONE's style requirements, including those for file naming. The PLOS ONE style templates can be found at https://journals.plos.org/plosone/s/file?id=wjVg/PLOSOne_formatting_sample_main_body.pdf and https://journals.plos.org/plosone/s/file?id=ba62/PLOSOne_formatting_sample_title_authors_affiliations.pdf

2. We note that you have stated that you will provide repository information for your data at acceptance. Should your manuscript be accepted for publication, we will hold it until you provide the relevant accession numbers or DOIs necessary to access your data. If you wish to make changes to your Data Availability statement, please describe these changes in your cover letter and we will update your Data Availability statement to reflect the information you provide.

3. Thank you for stating the following financial disclosure:

 [No].

At this time, please address the following queries:

1. Please clarify the sources of funding (financial or material support) for your study. List the grants or organizations that supported your study, including funding received from your institution.
2. State what role the funders took in the study. If the funders had no role in your study, please state: “The funders had no role in study design, data collection and analysis, decision to publish, or preparation of the manuscript.”
3. If any authors received a salary from any of your funders, please state which authors and which funders.
4. If you did not receive any funding for this study, please state: “The authors received no specific funding for this work.”

Please include your amended statements within your cover letter; we will change the online submission form on your behalf.

Additional Editor Comments (if provided):

[Note: HTML markup is below. Please do not edit.]

Reviewers' comments:

Reviewer's Responses to Questions

Comments to the Author

1. Does the manuscript provide a valid rationale for the proposed study, with clearly identified and justified research questions?

The research question outlined is expected to address a valid academic problem or topic and contribute to the base of knowledge in the field.

Reviewer #1: Yes

Reviewer #2: Yes

**********

2. Is the protocol technically sound and planned in a manner that will lead to a meaningful outcome and allow testing the stated hypotheses?

The manuscript should describe the methods in sufficient detail to prevent undisclosed flexibility in the experimental procedure or analysis pipeline, including sufficient outcome-neutral conditions (e.g. necessary controls, absence of floor or ceiling effects) to test the proposed hypotheses and a statistical power analysis where applicable. As there may be aspects of the methodology and analysis which can only be refined once the work is undertaken, authors should outline potential assumptions and explicitly describe what aspects of the proposed analyses, if any, are exploratory.

Reviewer #1: Yes

Reviewer #2: Yes

**********

3. Is the methodology feasible and described in sufficient detail to allow the work to be replicable?

Reviewer #1: Yes

Reviewer #2: Yes

**********

4. Have the authors described where all data underlying the findings will be made available when the study is complete?

The PLOS Data policy requires authors to make all data underlying the findings described in their manuscript fully available without restriction, with rare exception, at the time of publication. The data should be provided as part of the manuscript or its supporting information, or deposited to a public repository. For example, in addition to summary statistics, the data points behind means, medians and variance measures should be available. If there are restrictions on publicly sharing data—e.g. participant privacy or use of data from a third party—those must be specified.

Reviewer #1: Yes

Reviewer #2: Yes

**********

5. Is the manuscript presented in an intelligible fashion and written in standard English?

PLOS ONE does not copyedit accepted manuscripts, so the language in submitted articles must be clear, correct, and unambiguous. Any typographical or grammatical errors should be corrected at revision, so please note any specific errors here.

Reviewer #1: Yes

Reviewer #2: Yes

**********

6. Review Comments to the Author

Please use the space provided to explain your answers to the questions above and, if applicable, provide comments about issues authors must address before this protocol can be accepted for publication. You may also include additional comments for the author, including concerns about research or publication ethics.

You may also provide optional suggestions and comments to authors that they might find helpful in planning their study.

(Please upload your review as an attachment if it exceeds 20,000 characters)

Reviewer #1: comment-1: According to my understanding, the authors classified the electrical faults of rapier loom into common faults and other faults according to the frequency of occurrence by analyzing process and fault characteristics of rapier loom. Then an expert system is built in the field for edge computing based on knowledge fault diagnosis experience to diagnose common loom faults and reduce the computing pressure in the cloud.

comment-2: The authors claims that this study also "reduce the computing pressure in the cloud", but it is only written in abstract. The authors should also explain this point in intro, proposed and conclusion sections.

comment-3: Paper is well written. Authors should add limitations of the proposed work.

Comment-4: The table-1 can be written in more organized form such that to clear understanding about parameters.

comment-5: The authors should add some more words about HMI.

comment-6: The quality of the figures can be improved more especially the figure-6 and 7. Figures should be eye-catching not blur. It will enhance the interest of the reader.

commnet-7: The authors should add more clear detail in a paragraph on figure-4 by making comparison of used algorithms.

commetn-8: The classification results should also be present in abstract in 1 or 2 sentences.

comment-9: The summary at the end of the literature review should be focused on the limitations of related work.

commnet-10: Authors should explain at least the features of the dataset in a table.

commnet-11: Authors should add the most recent references related to cloud computing:

(1) M. Shabbir et al., "Enhancing Security of Health Information Using Modular Encryption Standard in Mobile Cloud Computing," in IEEE Access, vol. 9, pp. 8820-8834, 2021, doi: 10.1109/ACCESS.2021.3049564.

(2) A. R. Javed, M. Usman, S. U. Rehman, M. U. Khan and M. S. Haghighi, "Anomaly Detection in Automated Vehicles Using Multistage Attention-Based Convolutional Neural Network," in IEEE Transactions on Intelligent Transportation Systems, doi: 10.1109/TITS.2020.3025875.

(3) Swarna Priya R.M., Sweta Bhattacharya, Praveen Kumar Reddy Maddikunta, Siva Rama Krishnan Somayaji, Kuruva Lakshmanna, Rajesh Kaluri, Aseel Hussien, Thippa Reddy Gadekallu,

Load balancing of energy cloud using wind driven and firefly algorithms in internet of everything,

Journal of Parallel and Distributed Computing,

Volume 142,

2020,

Pages 16-26,

ISSN 0743-7315,

https://doi.org/10.1016/j.jpdc.2020.02.010.

(4) Thar Baker, Bandar Aldawsari, Muhammad Asim, Hissam Tawfik, Zakaria Maamar, Rajkumar Buyya,

Cloud-SEnergy: A bin-packing based multi-cloud service broker for energy efficient composition and execution of data-intensive applications,

Sustainable Computing: Informatics and Systems,

Volume 19,

2018,

Pages 242-252,

ISSN 2210-5379,

https://doi.org/10.1016/j.suscom.2018.05.011.

(5) M. Asim, Y. Wang, K. Wang and P. -Q. Huang, "A Review on Computational Intelligence Techniques in Cloud and Edge Computing," in IEEE Transactions on Emerging Topics in Computational Intelligence, vol. 4, no. 6, pp. 742-763, Dec. 2020, doi: 10.1109/TETCI.2020.3007905.

Reviewer #2: • In Introduction section, the drawbacks of each conventional technique should be described clearly.

• Introduction needs to explain the main contributions of the work more clearly.

• The authors should emphasize the difference between other methods to clarify the position of this work further.

• The Wide ranges of applications need to be addressed in Introductions

• The quality of the figures can be improved, in terms of resolution and dimensions. The authors can add the refer the applications of cloud. Load balancing of energy cloud using wind driven and firefly algorithms in internet of everything. Providing diagnosis on diabetes using cloud computing environment to the people living in rural areas of India. A Blockchain Based Cloud Integrated IoT Architecture Using a Hybrid Design.

**********

7. PLOS authors have the option to publish the peer review history of their article (what does this mean?). If published, this will include your full peer review and any attached files.

If you choose “no”, your identity will remain anonymous but your review may still be made public.

Do you want your identity to be public for this peer review? For information about this choice, including consent withdrawal, please see our Privacy Policy.

Reviewer #1: No

Reviewer #2: No

[NOTE: If reviewer comments were submitted as an attachment file, they will be attached to this email and accessible via the submission site. Please log into your account, locate the manuscript record, and check for the action link "View Attachments". If this link does not appear, there are no attachment files.]

While revising your submission, please upload your figure files to the Preflight Analysis and Conversion Engine (PACE) digital diagnostic tool, https://pacev2.apexcovantage.com/. PACE helps ensure that figures meet PLOS requirements. To use PACE, you must first register as a user. Registration is free. Then, login and navigate to the UPLOAD tab, where you will find detailed instructions on how to use the tool. If you encounter any issues or have any questions when using PACE, please email PLOS at figures@plos.org. Please note that Supporting Information files do not need this step.

Research on rapier loom fault system based on cloud-side collaboration

PONE-D-21-16599R1

Dear Dr. Wan,

We’re pleased to inform you that your manuscript has been judged scientifically suitable for publication and will be formally accepted for publication once it meets all outstanding technical requirements.

Within one week, you’ll receive an e-mail detailing the required amendments. When these have been addressed, you’ll receive a formal acceptance letter and your manuscript will be scheduled for publication.

An invoice for payment will follow shortly after the formal acceptance. To ensure an efficient process, please log into Editorial Manager at http://www.editorialmanager.com/pone/, click the 'Update My Information' link at the top of the page, and double check that your user information is up-to-date. If you have any billing related questions, please contact our Author Billing department directly at authorbilling@plos.org.

If your institution or institutions have a press office, please notify them about your upcoming paper to help maximize its impact. If they’ll be preparing press materials, please inform our press team as soon as possible -- no later than 48 hours after receiving the formal acceptance. Your manuscript will remain under strict press embargo until 2 pm Eastern Time on the date of publication. For more information, please contact onepress@plos.org.

Kind regards,

Thippa Reddy Gadekallu

Academic Editor

PLOS ONE

Additional Editor Comments (optional):

Reviewers' comments:

Reviewer's Responses to Questions

Comments to the Author

1. Does the manuscript provide a valid rationale for the proposed study, with clearly identified and justified research questions?

The research question outlined is expected to address a valid academic problem or topic and contribute to the base of knowledge in the field.

Reviewer #3: Yes

**********

2. Is the protocol technically sound and planned in a manner that will lead to a meaningful outcome and allow testing the stated hypotheses?

The manuscript should describe the methods in sufficient detail to prevent undisclosed flexibility in the experimental procedure or analysis pipeline, including sufficient outcome-neutral conditions (e.g. necessary controls, absence of floor or ceiling effects) to test the proposed hypotheses and a statistical power analysis where applicable. As there may be aspects of the methodology and analysis which can only be refined once the work is undertaken, authors should outline potential assumptions and explicitly describe what aspects of the proposed analyses, if any, are exploratory.

Reviewer #3: Yes

**********

3. Is the methodology feasible and described in sufficient detail to allow the work to be replicable?

Reviewer #3: Yes

**********

4. Have the authors described where all data underlying the findings will be made available when the study is complete?

The PLOS Data policy requires authors to make all data underlying the findings described in their manuscript fully available without restriction, with rare exception, at the time of publication. The data should be provided as part of the manuscript or its supporting information, or deposited to a public repository. For example, in addition to summary statistics, the data points behind means, medians and variance measures should be available. If there are restrictions on publicly sharing data—e.g. participant privacy or use of data from a third party—those must be specified.

Reviewer #3: Yes

**********

5. Is the manuscript presented in an intelligible fashion and written in standard English?

PLOS ONE does not copyedit accepted manuscripts, so the language in submitted articles must be clear, correct, and unambiguous. Any typographical or grammatical errors should be corrected at revision, so please note any specific errors here.

Reviewer #3: Yes

**********

6. Review Comments to the Author

Please use the space provided to explain your answers to the questions above and, if applicable, provide comments about issues authors must address before this protocol can be accepted for publication. You may also include additional comments for the author, including concerns about research or publication ethics.

You may also provide optional suggestions and comments to authors that they might find helpful in planning their study.

(Please upload your review as an attachment if it exceeds 20,000 characters)

Reviewer #3: The contribution is exciting and considerably novel. The paper is well written and starts with influencing motivation, and is reflected throughout the paper. I would like to accept this paper.

**********

7. PLOS authors have the option to publish the peer review history of their article (what does this mean?). If published, this will include your full peer review and any attached files.

If you choose “no”, your identity will remain anonymous but your review may still be made public.

Do you want your identity to be public for this peer review? For information about this choice, including consent withdrawal, please see our Privacy Policy.

Reviewer #3: No