The Seeding and Cultivation of a Tropical Species of Filamentous Ulva for Algal Biomass Production

Filamentous species of Ulva are ideal for cultivation because they are robust with high growth rates and maintained across a broad range of environments. Temperate species of filamentous Ulva are commercially cultivated on nets which can be artificially ‘seeded’ under controlled conditions allowing for a high level of control over seeding density and consequently biomass production. This study quantified for the first time the seeding and culture cycle of a tropical species of filamentous Ulva (Ulva sp. 3) and identified seeding density and nursery period as key factors affecting growth and biomass yield. A seeding density of 621,000 swarmers m-1 rope in combination with a nursery period of five days resulted in the highest growth rate and correspondingly the highest biomass yield. A nursery period of five days was optimal with up to six times the biomass yield compared to ropes under either shorter or longer nursery periods. These combined parameters of seeding density and nursery period resulted in a specific growth rate of more than 65% day−1 between 7 and 10 days of outdoor cultivation post-nursery. This was followed by a decrease in growth through to 25 days. This study also demonstrated that the timing of harvest is critical as the maximum biomass yield of 23.0±8.8 g dry weight m−1 (228.7±115.4 g fresh weight m−1) was achieved after 13 days of outdoor cultivation whereas biomass degraded to 15.5±7.3 g dry weight m−1 (120.2±71.8 g fresh weight m−1) over a longer outdoor cultivation period of 25 days. Artificially seeded ropes of Ulva with high biomass yields over short culture cycles may therefore be an alternative to unattached cultivation in integrated pond-based aquaculture systems.


Introduction
The global production of seaweeds (marine macroalgae) of 19 million tonnes is dominated by only five key species and their products are targeted for food and phycocolloid markets [1]. While less than 0.1% of total production is accounted for by green seaweeds [2], species within the genus Ulva have in many ways the most compelling characteristics for biomass applications in their cosmopolitan distribution [3], very high growth rates [4], high stocking densities [5,6], and wide environmental tolerances for year round production [7,8]. However, the existing commercial production of Ulva is either focussed on niche, high-value food products in Japan using controlled seeding with small production volumes ('aonori'; ,1,500 tonnes dry weight per annum; [9]) or on integrated aquaculture in land-based high rate algal ponds in South Africa using vegetative cultivation of biomass as abalone feed (,1,000 tonnes fresh weight per annum; [10]). There are also many studies that discuss the suitability of Ulva as biomass energy resource including biogas [11], ethanol and other alcohols [12] and biocrude [13]. In addition, the application of Ulva as a feedstock for nutraceuticals, in particular sulphated polysaccharides (ulvans), has been investigated [14,15]. To ensure a reliable and cost-effective biomass supply of Ulva, it is essential to develop and optimise the closed-life cycle production and yield of biomass, as a fundamental basis for commercial applications and more widespread production throughout the globe.
The genus Ulva can be categorised as having either a blade-like or filamentous (syn. Enteromorpha; [16]) morphology. In general, both morphologies can tolerate a wide range of environmental conditions and have high growth rates [8], that can result in the formation of algal blooms in eutrophic coastal waters ('green tides'). However, filamentous species, in particular, can have exceptional environmental tolerance and can grow in salinities ranging from 10 to 60 ppt [7] and temperatures up to 40uC [17]. Therefore, filamentous species of Ulva are ideal for cultivation across a broad range of environments and can be integrated into existing aquaculture production thereby providing value-adding processes and environmental services by removing dissolved nutrients from waste waters [18].
Filamentous species of Ulva can be maintained in free-floating cultures, either as 'germling clusters' [19] or using surface barriers [18,20]. However, many highly productive species of filamentous Ulva require a closed-life cycle with the production of seedlings and efficient seeding and cultivation techniques for the intensive production of biomass. For example, species of filamentous Ulva used in in the Asian cuisine, 'aonori' [21], have been cultivated since 1985 in Japan using nets. Traditionally, seedlings have been obtained from natural settlement by submerging nets in calm areas with naturally high abundances of the desired species [9]. Spores released from natural populations then settle on the nets which are subsequently transferred to cultivation grounds [22]. However, natural seeding provides for little control over the density of seeding and distribution. In contrast, artificial seeding allows for a high level of control and seeding techniques have been investigated since the 1980s [23,24].
The practise of artificial seeding relies heavily on manipulative treatments to induce reproduction independent of seasonal reproduction patterns. A reliable method for artificially inducing reproduction with high reproductive output has been successfully demonstrated for the filamentous species of Ulva, Ulva sp. 3 [25]. This species has only recently been described [26] and its distribution ranges from the East coast of Australia [8] to Southern Japan [26]. Ulva sp. 3 is a robust species with high growth rates across a wide range of temperatures [8] and a salinity tolerance from brackish [26] to saline [8], making it ideal for cultivation for biomass applications. In order to achieve commercially viable cultivation of this target species, fundamental data on the optimal density of seeding and nursery period are first required, followed by an understanding of how these initial conditions influence growth at scale. Seeding density is directly related to intraspecific competition for resources, particularly light and nutrients, which can result in reduced growth and increased mortality [27][28][29]. Similarly, the nursery period is critical to minimise the detachment and loss of germlings due to hydrodynamic forces [30]. Notably, an increased contact time with the surface enhances overall settlement [31] and the adhesion strength of settled spores [32].
The aim of this study was therefore to establish optimum density of settled swarmers and nursery conditions for Ulva sp. 3 that results in high biomass yields. To determine the optimal seeding density for Ulva sp. 3, ropes were artificially seeded under controlled conditions using swarmers (collective term for motile reproductive bodies, including gametes, zoospores, zoids). The seeding densities ranged from 155 to 1,552610 3 swarmers m 21 rope. In addition, nursery periods from one to ten days were tested for theses densities and subsequently, the seeded ropes were maintained in outdoor tanks for 21 days to determine weekly growth rates. Finally, ropes were seeded at the optimal density and were, after the optimum nursery period of five days, maintained in outdoor tanks for up to 25 days to determine biomass yields, growth rates, fresh weight to dry weight ratio (FW:DW), ash content, and the morphology of filaments over this period.

Collection of algal biomass and preparation of reproductive material
The species used in this study was Ulva sp. 3 [26] and identified using molecular barcoding [8,25]. Ulva sp. 3 (hereafter Ulva) was characterised by flat tubular thalli and collected in the morning by hand from a land-based aquaculture facility at Guthalungra (19u559S, 147u509E), Queensland, Australia. Permission was obtained from owners to collect algae from this site. Samples were placed in a 25 L container filled with pond water and then transported within 3 h to the laboratory at James Cook University in Townsville, Australia. Subsequently, the samples were gently washed three times with filtered seawater (FSW; 0.2 mm and UV sterilised) to remove debris, epiphytes and invertebrates. To induce the release of swarmers, Ulva was shocked at a temperature of 4uC for 10 min [25] and subsequently chopped using a blender in the early afternoon on the day of collection. The chopped filaments were retained with a sieve (120 mm), washed with autoclaved FSW and subsequently placed in a crystallising dish filled with approximately 200 mL autoclaved FSW. Approximately 0.5-1 mL of this suspension was then transferred in Petri dishes filled with 10 mL autoclaved FSW using a transfer pipette and subsequently placed in a temperature controlled culture cabinet (Sanyo MLR-351) at 25uC at an irradiance of 125 mmol photon m 22 s 21 under a 12 h L: 12 h D photoperiod to maximise the release of swarmers [25]. The release of swarmers peaked after two days between 10:00 and 11:30 am. The Petri dishes were then emptied in a beaker through a sieve (120 mm) to filter out the chopped filaments, while the released swarmers were collected with the seawater in the beaker. The density of the swarmers was calculated using a haemocytometer.

Optimal seeding density and nursery period
To determine which seeding density and nursery period resulted in the highest biomass yield and growth, swarmers were seeded onto polypropylene ropes (Ø 4 mm, Syneco) at densities of 155, 310, 466, 621, and 1,552610 3 swarmers m 21 rope. A total of 45 pieces of rope were seeded, each with a length of 580 mm. These were attached to the bottom of individual Petri dishes (Ø 60 mm, Techno Plas; S6014S10) as a flat spiral coil using the pressuresensitive adhesive Ezy Tack (Selleys). The seeding density was altered by manipulating the density of swarmers to 5, 10, 15, 20, and 50610 3 swarmers mL 21 and then adding 18 mL of this swarmer suspension to each Petri dish with a piece of rope using a syringe. The tested nursery periods were 1, 5, and 10 days and the Petri dishes were kept in a culture cabinet (Sanyo MLR-351) in a 12 h L:12 h D photoperiod at 25uC during this period. The water was changed, where applicable, after 3, 5, and 8 days. There were three replicates (n = 3) for each seeding density for each tested nursery period. Subsequent to the time in the nursery, the seeded ropes were carefully removed from the Petri dishes using tweezers, uncoiled and transferred to aerated flow-through outdoor tanks under ambient light at the Marine & Aquaculture Research Facilities Unit (MARFU).
A total of 5 seeded ropes (one from each density) were attached to a weighted frame (3806500 mm) using cable ties. Each frame was placed on the bottom of a tank (n = 9 replicate tanks) so that the ropes were immersed horizontally in the water at a depth of approximately 100 mm below the surface. To minimise temperature fluctuations, the tanks holding the ropes were placed in a circulating water bath (see cultivation conditions following). After 7, 14, and 21 days of outdoor cultivation, the tanks, frames and air lines were cleaned and the seeded ropes were repeatedly sampled to measure the fresh weight (FW) of Ulva. The ropes were spun dry and weighed (FW) using a digital balance (Kern KB 3600-2N). After 21 days of outdoor cultivation, the seeded ropes were dried in an oven at 65uC for at least 7 days to determine the dry weight (DW) of Ulva. The fresh and dry biomass yield was calculated as FW (g FW m 21 rope) and DW (g DW m 21 rope) per linear meter of rope, respectively. Individual FW:DW ratios were calculated for each replicate. Specific growth rate was calculated for each replicate using the equation SGR (% day 21 ) = ln (B 2 /B 1 )/ (t 2 -t 1 ) ? 100, where B 1 and B 2 are the biomasses (g FW) at time t 1 and t 2 of outdoor cultivation (days).
Experiments were conducted during the Australian winter with an average water temperature of 25uC and the seeded ropes received on average photosynthetically active radiation of 29. Biomass yield and growth of Ulva seeded at optimal seeding density and nursery period To determine the dry biomass yield, growth, FW:DW ratio, ash content and change in morphology over time, ropes were seeded at an optimal density of 621,000 swarmers m 21 rope and maintained for five days under nursery conditions (see results 'Optimal seeding density and nursery period'). The arrangement of ropes in Petri dishes, and the seeding and nursery procedure, followed the methods described in the previous experiment. After five days under nursery conditions, the seeded ropes were removed from the Petri dishes and transferred to aerated flow-through outdoor tanks at MARFU as described above. Each seeded rope was individually attached to a weighted frame placed on the bottom of a tank holding approximately 28 L of FSW (1 mm and UV sterilised) for 25 days. Holding tanks, frames and air lines were cleaned after 7, 13, and 19 days. The seeded ropes were destructively sampled (n = 3) after 7, 10, 13, 16, 19, 22, and 25 days of outdoor cultivation and photographed with a digital camera (Canon PowerShot D20) to determine the width of filaments (n = 50 per samples) using Image J freeware (www.nih.giv). Subsequently, samples were spun dry and weighed to determine the growth (SGR) using the equation above where B 1 and B 2 are the average biomasses (g FW). Thereafter, the samples were dried in an oven at 65uC for at least 7 days to quantify the DW and to calculate the dry biomass yield as DW per linear meter of rope (g DW m 21 rope). FW:DW ratios were calculated as described above. The ash content of each replicate was quantified by heating a 1.5 g homogenised subsample of dried biomass at 110uC in a moisture balance until a constant dry weight was reached and then combusting at 550uC in a muffle furnace for 24 h until a constant weight was reached.
Experiments were conducted with a total of three independent sample collections of Ulva as initial parent generation used as a source of swarmers to seed the ropes during the Australian spring (hereafter referred to as 'batch'). The water temperatures in the tanks ranged between a night time minimum of 21.7uC and a daytime maximum of 36.4uC during the trial, with an average water temperature of 27.

Statistical analysis
Data were analysed by permutational analysis of variance (PERMANOVA) using PRIMER 6 (v. 6.1.13) and PERMA-NOVA+ (v. 1.0.3) [33]. The Bray-Curtis dissimilarity measure was used for all PERMANOVAs and p-values were calculated using permutation of residuals under a reduced model with 9999 random permutations. If there was a significant difference, pairwise a posteriori comparisons were made among the significant groups using the Bray-Curtis similarity measure (a = 0.05). All data are reported as mean 61 standard error (S.E.) unless stated otherwise.
To formally test the effect of seeding density on the biomass yields (fresh and dry) after 21 days of outdoor cultivation for each nursery period in the first experiment, density was considered as a fixed factor and tank as an unreplicated blocking factor as seeded ropes in one tank were not independent. To determine the effect of nursery period and sampling day on the fresh biomass yields of seeded ropes, the optimal seeding density of 621,000 swarmers m 21 (see results) was selected for PERMANOVA analysis and nursery was considered as fixed and sampling day as random factors. To analyse the effect nursery period on the dry biomass yield after 21 days of outdoor cultivation of ropes seeded at 621,000 swarmers m 21 , data was analysed using an one-factor PERMANOVA. To test for the effect of sample collection on the dry biomass yield, FW:DW ratio, SGR, ash content, and width of filaments over time in the second experiment, two-factor PERMANOVAs were used with time as a fixed factor (with destructively sampled replicates) and sample collection as a random factor. FW:DW ratios for both experiments were correlated with dry biomass yield for each replicate using the software Statistica (v.12).

Optimal seeding density and nursery period
The highest fresh biomass yields were obtained for ropes maintained for five days in the nursery, regardless of seeding density, and had approximately two to six times the biomass than ropes maintained under shorter and longer nursery periods ( Figure 1). The highest fresh biomass yield was obtained for the seeding density of 621,000 swarmers m 21 rope after the nursery period of five days, and this density was nearly double the yield obtained at any other seeding density and nursery period ( Figure 1). Therefore, this seeding density in combination with a five day nursery period was chosen for the subsequent experiment on the basis of biomass yield. When specifically analysing the fresh biomass yield of ropes seeded at 621,000 swarmers m 21 rope to identify differences between nursery periods over time within a single seeding density, there was a significant interactive effect between nursery and days of outdoor cultivation, driven by significant differences between nursery periods and lower biomass yields overall after day 7 in comparison to day 14 and 21 (Table 1).
After the shortest nursery period (one day), the average fresh biomass yields increased for all seeded ropes over 21 days and also increased with increasing seeding densities (Figure 1a). The lowest biomass yields were observed after seven days and were below 0.4 g FW m 21 rope for all seeding densities. In the following days, the yields increased more than 10-fold and ranged from 5.561.4 g FW m 21 rope to 27.567.1 g FW m 21 rope after 14 days and from 12.164.3 g FW m 21 rope to 48.5617.1 g FW m 21 rope after 21 days (Figure 1a). The highest seeding density of 1,552610 3 swarmers m 21 rope had a greater biomass yield than lower seeding densities after a nursery period of one day, despite some variability between tanks in the analysis ( Table 2).
After the nursery period of five days, the biomass yields were generally low after seven days and increased approximately 16fold during the following days, ranging from 30.8610.9 g FW m 21 rope to 72.566.6 g FW m 21 rope at day 14. Subsequently, the yields decreased after 21 days and ranged from 17.765.8 g FW m 21 rope to 42.967.9 g FW m 21 rope (Figure 1b).
After the longest nursery period (ten days), the biomass yields ranged from 10.161.9 g FW m 21 rope to 18.261.3 g FW m 21 rope after seven days (Figure 1c) and were generally higher than for shorter nursery periods. However, the biomass yields overall were low for the following days and below 23 g FW m 21 rope at all times, which is less than half the yield than that of shorter nursery periods.
Similar to the fresh biomass yields, the dry biomass yields overall were generally higher for ropes maintained at a nursery period of five days (4.260.5 g DW m 21 rope) compared to shorter (3.160.6 g DW m 21 rope) and longer nursery stages (1.860.3 g DW m 21 rope) ( Figure 2). The average dry biomass yields ranged from 2.460.8 g DW m 21 rope to 5.661.2 g DW m 21 rope for a nursery period of five days, and were halved for a longer nursery period of ten days where yields ranged from 0.860.1 g DW m 21 rope to 2.761.0 g DW m 21 rope. Notably, the dry biomass yields were measured after 21 days of outdoor cultivation when the biomass on ropes maintained under a nursery period of five days had already degraded, on contrast to the shorter nursery period of one day which continued to increase. Nursery period had no significant effect when specifically analysing the dry biomass yield  Table 1. PERMANOVA analysis on Bray-Curtis distances testing the effects of nursery period (Nursery, fixed factor) and days of outdoor cultivation (Day, random factor) on the fresh biomass yield of ropes seeded at 621610 3 swarmers m 21 rope; and the effect of nursery on the dry biomass yield after 21 days outdoor cultivation. of ropes seeded at a single seeding density ( Table 1). The dry biomass yield increased nearly 3-fold from the lowest seeding density of 155,000 swarmers m 21 rope (1.660.4 g DW m 21 rope) to the highest seeding density of 1,552610 3 swarmers m 21 rope (4.360.9 g DW m 21 rope) ( Figure 2) with significant differences in dry biomass yield between seeding densities for nursery periods of one and ten days ( Table 2). The average FW:DW ratios were highly variable ranging from 4.761.0 to 8.660.3 and generally decreased with increasing nursery periods with no consistent trend between FW:DW ratio and seeding density. There was no correlation between the FW:DW ratio and the dry biomass yield (r = 0.185, p = 0.224 ).
In contrast to fresh and dry biomass yields, specific growth rates were highest for the shortest nursery period of one day across all seeding densities because of the low initial biomass for each measurement (Figure 3). The average growth rates for Ulva maintained at a nursery period of one day ranged from 46.461.7 % day 21 to 64.461.0 % day 21 between 7 and 14 days of outdoor cultivation, while those maintained under the longest nursery period of ten days ranged from 2.462.6 % day 21 to 9.561.6 % day 21 (Figure 3a). The growth rates between 14 and 21 days of outdoor cultivation had substantially lower growth rates with the shortest nursery period being the only treatment with positive values (Figure 3b).
Biomass yield and growth of Ulva seeded at optimal seeding density and nursery period The average dry biomass yield increased more than 10-fold from day 7 (1.860.5 g DW m 21 rope) to day 10 (10.164.9 g DW m 21 rope) and then day 13 (23.068.8 g DW m 21 rope) (Figure 4a). Subsequently, the biomass yield decreased to below 20.4 g DW m 21 rope for extended time periods of outdoor cultivation. There was a significant interaction of batch and days of outdoor cultivation (Table 3), driven by differences in the time when the highest biomass yield was attained among batches ( Figure 4b). While the biomass yield peaked at day 13 for the first batch (40.063.3 g DW m 21 rope) and third batch (19.062.8 g DW m 21 rope), the second batch had the highest biomass yield at day 16 (16.260.4 g DW m 21 rope). Furthermore, there were striking differences in the biomass yield between batches; however, batches showed a similar trend of an initial increase and subsequent decrease in dry biomass yield over time (Figure 4b).
Notably, the biomass matured and was reproductive during the Table 2. PERMANOVA analysis on Bray-Curtis distances testing the effects of seeding density (Density, fixed factor) on the (a) fresh (g FW m 21 rope) and (b) dry biomass yield (g DW m 21 rope) of seeded ropes at each nursery period in an unreplicated blocked design (Tank: blocked factor) after 21 days outdoor cultivation.  course of the experiment and the release of swarmers occurred after 13 days of outdoor cultivation. Average specific growth rates decreased significantly over time (Figure 4c, Table 3) with the highest growth rate between 7 and 10 days of outdoor cultivation (67.1612.2 % day 21 ). There was a subsequent reduction in growth rate between 10 and 13 days (29.9610.9 % day 21 ). After 13 days of outdoor cultivation, growth rates were generally lower and ranged from 213.4616.4 % day 21 (days 13 to 16) to 3.569.8 % day 21 (days 16 to 19). Average FW:DW ratios ranged from 5.960.5 (day 7) to 8.961.3 (day 13) (Figure 5a) and overall patterns were generally variable between batches, reflected by a significant interaction between batch and days of outdoor cultivation (Table 3). In addition, FW:DW ratios were positively correlated with an increase in dry biomass yield (r = 0.788, p,0.001). The average width of filaments increased more than 7-fold from day 7 (86.767.0 mm) to day 19 (644.36158.4 mm) (Figure 5b). Subsequently, the average width decreased to 390.3673.7 mm and 390.6663.0 mm at days 22 and 25, respectively. The ash content ranged from 25.960.6 % (day 7) to 36.264.9 % (day 13) (Figure 5c).

Discussion
This study demonstrates the importance of seeding density and nursery period on the biomass yield and growth rate of Ulva sp. 3 when artificially seeded onto ropes. Optimal cultivation conditions resulting in the highest biomass yields were achieved at a seeding density of 621,000 swarmers m 21 rope and a nursery period of five days. Seeding density was a key factor affecting both growth rate and biomass yield of Ulva sp. 3 confirming previous studies, where the biomass and size of seaweeds was related to their settlement density [27,30,34]. In general, the density of germlings is negatively related to growth and survival due to intraspecific competition and shading effects [27], yet low seeding densities on ropes can result in higher growth of epiphytes and thus high seeding densities are also a strategy to control biofouling on cultured seaweeds [35]. However, this might be less critical for fast-growing and opportunistic species such as filamentous Ulva, meaning that the selection of seeding density can be based on  controlled cultivation conditions. In addition, the optimal seeding density for Ulva of 621,000 individuals m 21 rope, as quantified in this study, is generally much higher than for other species, where common seeding densities are 2,000 individuals m 21 rope for the brown seaweeds Undaria pinnatifida [36] and Sargassum fulvellum [37], 2,000 to 3,000 individuals m 21 rope for Saccharina latissima [38,39], and 20,000 individuals m 21 rope for the red seaweed Gracilaria chilensis [40]. Furthermore, brown and red seaweeds typically have longer nursery and culture cycles with correspondingly higher productivities expected per linear metre (,7 kg FW m 21 rope after 5 months for G. chilensis; [40]). This highlights the differences in the morphology and cultivation techniques of commercial brown and red seaweeds compared to filamentous Ulva, with clear distinction in the length of production cycle.  Table 3. PERMANOVA analysis on Bray-Curtis distances testing the effects of days of outdoor cultivation (Day, fixed factor) and batch (Batch; random factor) on the biomass yield per metre rope (Fresh biomass; Dry biomass), FW:DW ratios (FW:DW), width of filaments (Width), ash content (Ash) and specific growth rate (SGR) of Ulva. A further key factor affecting growth and biomass yield of Ulva was the nursery period prior to grow-out. This period is critical for the success of viable mass-cultivation of Ulva as an increased contact time acts to minimise detachment and loss of germlings due to hydrodynamic forces [30]. This effect is consistent with the difference in fresh biomass yields for seeded ropes maintained under nursery conditions for one and five days where values were lower for the shorter nursery period, most probably due to higher detachment of settled germlings after only one day. Interestingly, an extended nursery period of ten days had adverse effects on the growth of Ulva with the lowest biomass yields and growth rates overall among nursery periods. This implies that resources may be limited under static nursery conditions [41,42] resulting in poor growth performance of the germlings.
The trend of initially increasing and then decreasing biomass yield, coupled with decreasing growth rates over time, is likely due to a general decrease of light availability with increasing biomass on the ropes [43]. Furthermore, the decline in growth of Ulva sp. 3 also reflects the maturation of biomass and the reproductive events after 13 days of outdoor cultivation. This short life cycle is characteristic of opportunistic species and is notably also shorter than other species of Ulva, including U. ohnoi (,3 weeks; [44]) and tropical U. flexuosa (,4 weeks; [34]), and much shorter than the life cycle for other seaweed species (Sargassum horneri; ,4.5 months; [45]). Vegetative cells of Ulva transform directly into reproductive cells and, therefore, maturation and reproduction results in the degradation of filaments once the swarmers have been released. As such, the timing of harvest is critical to maximise yields. Furthermore, it is also important if mature populations on the ropes are to be used as parental stock for future generations through artificial seeding.
The species Ulva sp. 3 is an ideal candidate for biomass applications with its high biomass yields and growth rates as shown in this study, and its ability to integrate with existing aquaculture facilities [8], which together promise to make algal cultivation for biomass applications more cost-effective. The specific growth rate was high at more than 65% day 21 which is higher than recorded in a previous laboratory study (,30% day 21 ; [8]). Overall, the growth rate was higher than for other species of Ulva and macroalgae, such as U. reticulata (,4% day 21 ; [46]), U. ohnoi (,38% day 21 ; [4]), Cladophora and Chaetomorpha (,44% day 21 ; [47]), Saccharina latissima (,5% day 21 ; [48]), and Porphyra linearis (,16% day 21 ; [49]). Furthermore, Ulva sp. 3 was a robust species in this study tolerating varying environmental conditions across the experimental period. Water temperatures reached up to 36.4uC, without any signs of degradation of biomass, and other species of filamentous Ulva can be grown in water temperatures up to 40uC [17]. In addition, filamentous species of Ulva generally have a broad tolerance towards a wide range of salinities, including as low as 5 psu over 7 days, without a significant decrease in the viability of cells [50]. This supports Ulva sp. 3 as a promising candidate for year-around cultivation in tropical environments which are typically characterised by strongly seasonal rainfall providing a challenge for the consistent masscultivation of less robust algal species [51]. Finally, Ulva sp. 3 is a native species common at land-based aquaculture facilities in Eastern Australia and could therefore also be considered for bioremediation of waste waters from land-based aquaculture [8]. We suspect that similar results will be achievable for other filamentous species of Ulva with similar seeding density and nursery period based on similarities in morphology and size between species.
In conclusion, this study highlights the importance of controlling seeding densities in culture with large effects of doubling of the biomass yield at an optimal range per length of rope or potentially any unit of culture infrastructure. Therefore, ropes artificially seeded at an optimal density under controlled conditions will importantly maximise yields with an efficient use of the resource inputs and this provides a fundamental step in the cultivation of filamentous Ulva at scale. A reliable source of biomass for yearround production through optimised hatchery and culture cycles, in line with maximising biomass production per unit effort, allows for a reliable bioremediation strategy and further permits the development and management of selected breeding lines (genotypes). This study also revealed striking differences in the biomass yield between batches and underlines the need to select genotypes with high productivity for the cultivation of this species and to test the potential interactive effects with environmental conditions. Finally, populations seeded onto ropes can be used as parental plants for seedling production, which in turn reduces the need to harvest wild stocks.