Synthesis and Detection of Oxygen-18 Labeled Phosphate

Phosphorus (P) has only one stable isotope and therefore tracking P dynamics in ecosystems and inferring sources of P loading to water bodies have been difficult. Researchers have recently employed the natural abundance of the ratio of 18O/16O of phosphate to elucidate P dynamics. In addition, phosphate highly enriched in oxygen-18 also has potential to be an effective tool for tracking specific sources of P in the environment, but has so far been used sparingly, possibly due to unavailability of oxygen-18 labeled phosphate (OLP) and uncertainty in synthesis and detection. One objective of this research was to develop a simple procedure to synthesize highly enriched OLP. Synthesized OLP is made up of a collection of species that contain between zero and four oxygen-18 atoms and, as a result, the second objective of this research was to develop a method to detect and quantify each OLP species. OLP was synthesized by reacting either PCl5 or POCl3 with water enriched with 97 atom % oxygen-18 in ambient atmosphere under a fume hood. Unlike previous reports, we observed no loss of oxygen-18 enrichment during synthesis. Electrospray ionization mass spectrometertry (ESI-MS) was used to detect and quantify each species present in OLP. OLP synthesized from POCl3 contained 1.2% P18O16O3, 18.2% P18O2 16O2, 67.7% P18O3 16O, and 12.9% P18O4, and OLP synthesized from PCl5 contained 0.7% P16O4, 9.3% P18O3 16O, and 90.0% P18O4. We found that OLP can be synthesized using a simple procedure in ambient atmosphere without the loss of oxygen-18 enrichment and ESI-MS is an effective tool to detect and quantify OLP that sheds light on the dynamics of synthesis in ways that standard detection methods cannot.


Introduction
The lack of multiple stable isotopes of P has led researchers to study the ratio of 16 O and 18 O in phosphate, the dominant form of P in the natural environment. The naturally occurring ratio of 18 O/ 16 O bonded to phosphorus in phosphate, expressed as d 18 O p , has been used to infer the source of P in water bodies [1][2][3][4][5][6]. Gruau et al. [7] found substantial variability of d 18 O p within P sources and considerable overlap of d 18 O p among different P sources and therefore questioned the value of this method as a research tool. Based on the variability and overlap of d 18 O p in natural sources, some researchers have used a method that enriches phosphate in oxygen-18, making it very distinct from any other P sources. The synthesis of oxygen-18 labeled phosphate (OLP) is generally carried out by hydrolyzing either PCl 5 or POCl 3 with water enriched with oxygen-18. This reaction is typically carried out in an atmosphere devoid of moisture to prevent the highly reactive PCl 5 or POCl 3 from reacting with atmospheric water [8][9][10][11]. Middleboe and Saaby Johansen [12] reported that up to one-half of the 18 O enrichment was sacrificed when POCl 3 was hydrolyzed with H 2 18 O in ambient atmosphere. Analysis of the 18 O/ 16 O ratio of OLP has been previously carried out through the use of optical emission spectroscopy [9,13,14], in which the OLP present in solution, plant tissue (after being extracted with 0.5 M HCl), or soil (after being extracted with anion exchange resin) is precipitated as struvite (MgNH 4 PO 4 ?6H 2 O) [9,14]. This precipitate is pyrolyzed to carbon monoxide, which is analyzed for its 18 O/ 16 O ratio by optical emission spectroscopy [14]. Synthesized OLP is made up of a collection of species that contain between zero to four oxygen-18 atoms. Optical emission spectroscopy is only capable of determining an overall 18 O/ 16 O ratio and is not able to distinguish between the various OLP species. The use of electrospray ionization mass spectrometry (ESI-MS) has also been presented as a viable means to determine the 18 O/ 16 O ratio of OLP and as a detection tool that can differentiate between OLP species. OLP dissolved in water was analyzed by ESI-MS and the results were compared to those obtained with 31 P NMR analysis. The authors reported good agreement between the ESI-MS and 31 P NMR results [11]. However, ESI-MS is sensitive at mg L 21 P levels, which is lower than 31 P NMR limits of detection.
The first objective of this research was to develop a simpler, efficient technique for the synthesis of OLP. The second objective was to use ESI-MS to quantify the individual OLP species present in synthesized OLP compounds. A final objective included determining the stability of OLP stored in sterile conditions over a period of several months.

Methods
The synthesis of OLP was carried out after consultation with the University of Wisconsin-Madison Environment, Health and Safety Department (Madison, Wisconsin) as POCl 3 and PCl 5 are both highly toxic chemicals. A chemical resistant suit, chemical resistant gloves, and a positive pressure, self-contained breathing apparatus (Scott Health and Safety, Monroe, North Carolina) were worn during the handling of these chemicals and during their reaction with water to prevent any contact or inhalation of fumes.

OLP Synthesis from POCl 3
The synthesis of OLP from POCl 3 was carried out in a 256200 mm glass test tube contained within a 250 mL Erlenmeyer flask filled with 150 mL of water to moderate the temperature. The flask and test tube were placed on a combination stir/hot plate within a fume hood. OLP was synthesized through the following spontaneous and highly exothermic reaction: 2.00 g of water with 97 atom % 18 O (Sigma-Aldrich, St. Louis, Missouri) were added to the test tube, followed by 4.87 g of POCl 3 (Pfaltz and Bauer Inc., Waterbury, Connecticut) added drop wise while stirring with a magnetic stir bar. Labeled water was added in 10% excess to ensure that the POCl 3 reacted completely with water containing 18 O. After the vigorous reaction subsided, the test tube was heated for 2 h at 100uC with stirring to remove HCl produced during the reaction. Following heating, the test tube was allowed to cool to room temperature and 5 M KOH was added to raise the pH to 4.7. The KH 2 PO 4 product was diluted with ultrapure water, and the P concentration of this solution was determined using an IRIS Advantage inductively coupled plasma optical emission spectrometer (ICP-OES) (Thermo Jarrell Ash, Franklin, Massachusetts). The reaction was carried out with pure POCl 3 , and with POCl 3 stored for a period of 6 and 17 months after it was initially opened to determine if there was any effect of long term POCl 3 storage on the OLP species composition.

OLP Synthesis from PCl 5
The synthesis of OLP from PCl 5 was carried out using the same procedure as described above, but this time reacting 2.50 g of PCl 5 (Sigma-Aldrich, St. Louis, Missouri) with 1.00 g of water containing 97 atom % 18 O (Sigma-Aldrich, St. Louis, Missouri) through the following spontaneous and highly exothermic reaction: The reaction was carried out with freshly opened PCl 5 , and PCl 5 that was stored for a period of 17 months after it was initially opened.

Quantification of Species Using ESI-MS and Long-Term Stability of OLP in Sterile Water
Electrospray ionization mass spectrometry (ESI-MS) was used to establish a ratio of each of the species present in the synthesized OLP. All samples were analyzed using an Agilent 1100 LC-MSD SL single-quadrupole model 1946D mass spectrometer (Agilent Technologies, Santa Clara, California). Table 1 lists the liquid chromatography (LC) and mass spectrometer (MS) conditions used for this analysis. The samples were diluted to approximately 60 mg L 21 P prior to analysis and analyzed in duplicate injections. Oxygen labeled phosphate eluted from the LC beginning at ,4.2 min and ending at 4.5 min after injection. During OLP analysis by ESI-MS, the m/z range monitored was 90-120, as the peaks of interest were m/z 97 (H 2 P 16  ). All other peaks within this range were negligible (Fig. 1). The area of each spectra for individual phosphate species were compared to the cumulative area of all the phosphate species allowing for the calculation of the relative contribution of each phosphate species shown in Figure 1. This relative information was used with the total P concentration of the sample to calculate the concentration of phosphate species in solution.
To monitor the stability of OLP solutions in a sterile environment, aqueous OLP solutions were diluted with autoclaved ultrapure water, placed in autoclaved polypropylene containers, and stored in darkness at 4uC.

Results
Data from the ESI-MS analysis of OLP synthesized from POCl 3 and PCl 5 are shown in Tables 2 and 3, respectively, along with the theoretical synthesis values. Theoretical values were calculated assuming completely random arrangement of the oxygen atoms from labeled water and assuming no P-O bonds of POCl 3 were broken. We observed almost no loss of oxygen-18 enrichment when synthesizing OLP from pure POCl 3 (Table 2). However, OLP synthesized from POCl 3 stored six months had an oxygen-18 content of 62.2% and POCl 3 stored 17 months had an oxygen-18 content of 55.3%. This enrichment loss can probably be attributed to water vapor entering the POCl 3 container either when the bottle was opened or throughout the storage period. There was no loss of oxygen-18 enrichment when synthesizing OLP from PCl 5 that had been stored for 17 months after it was initially opened (Table 3). Based on the results from the reaction of PCl 5 with 97 atom % 18 O water carried out in ambient atmosphere (Table 3) in December 2008, completely labeled P 18 O 4 made up 90.0% of the species present and the overall oxygen-18 content of the OLP was 97.0%.
There was very little deviation between the theoretical values and actual values of the OLP species present in OLP synthesized from PCl 5 (Table 3). However, large differences between the theoretical values and actual values of the amount of each OLP species present in OLP synthesized from POCl 3 were observed ( Table 2). One unexpected result of the synthesis of OLP from POCl 3 was the formation of a significant amount of P 18 O 4 (m/z 105), which made up 13.0% of the OLP synthesized from fresh POCl 3 . This is noteworthy because the POCl 3 starting material contains one oxygen atom that was expected to remain bonded to the P atom, preventing the formation of P 18 O 4 . The natural abundance of oxygen-18 at 0.2% does not explain this level of P 18 O 4 production. After observing these results, we hypothesized that the amount of energy released during the reaction between POCl 3 and water was enough to break the P-O bond in POCl 3 , thus resulting in a random assortment of the oxygen-16 and oxygen-18 atoms bonded to the P atoms. We predicted the expected synthesis outcome based on all the P-O bonds in POCl 3 breaking and the total amount of oxygen-18 (73.0%) and oxygen-16 (27.0%) contained in the synthesized OLP, (Table 4). Based on the differences between the expected and actual results, especially for the OLP species at m/z 103 (P 18 O 3 16 O) and 105 (P 18 O 4 ), it appears that some of the O atoms present in the POCl 3 starting material remained bonded to the P atom during the reaction with water, while the bond between other POCl 3 O atoms and P was broken.
The extent of broken P-O bonds in POCl 3 during OLP synthesis was calculated using an implicit equation that reduced the overall 97% oxygen-18 enrichment by an amount equal to the extent of broken bonds supplying additional oxygen-16. This calculation allowed those POCl 3 molecules with broken P-O bonds to react with four O atoms from the O isotope pool and those with no broken P-O bonds to react with three O atoms. Solutions to the equation were iterated comparing the measured isotopic ratios with those predicted until the sum of squares of the differences was minimized. The results show close agreement between the actual amount of each OLP species synthesized and the predicted values ( Table 5). The results of the calculation suggest that 17.9% of the P-O bonds in POCl 3 were broken during the December 2008 synthesis, while 38.4% of the bonds were broken during the May 2010 synthesis.
The OLP solutions were synthesized with fresh POCl 3 and PCl 5 in December 2008 and they were analyzed by ESI-MS 16 months later in April 2010. After the 16 month period, the total oxygen-18 content of the OLP solutions synthesized from POCl 3 and PCl 5 were 73.0% and 97.0%, respectively. This indicates that there was no O exchange between phosphate and water, which is in agreement with Blake et al. [15] and McLaughlin and Paytan [16].

Discussion
These synthesis reactions were carried out in ambient air under a fume hood using a fairly simple procedure as compared to previous synthesis attempts. Middleboe and Saaby Johansen [12] reported a loss of about one-half of the expected oxygen-18 enrichment when synthesizing OLP in ambient atmosphere from POCl 3 , which they suggested should be expected for any OLP synthesis carried out in ambient atmosphere. Based on the reaction of POCl 3 with water that contains 97 atom % 18 O, it would be expected that the maximum amount of oxygen atoms being oxygen-18 would be 72.8% (assuming that 0.2% of the POCl 3 oxygen atoms are oxygen-18 based on the natural abundance of oxygen-18). Additionally, based on the reaction between PCl 5 and 97 atom % 18 O water, one would expect the maximum amount of oxygen-18 atoms to be 97%. Following Middleboe and Saaby Johansen [12], we would have expected only 36.5% of the phosphate oxygen atoms in the OLP synthesized from POCl 3 and 48.5% of the phosphate oxygen atoms in the OLP synthesized from PCl 5 would be oxygen-18. However, our enrichment levels were substantially greater for both POCl 3 and PCl 5 ( Table 2). In fact, we observed almost no loss of oxygen-18 enrichment by performing the reactions in ambient air. It is possible that the loss of oxygen-18 enrichment reported by Middleboe and Saaby Johansen [12] when synthesizing OLP in ambient atmosphere was the result of decreased POCl 3 purity as the result of reaction with atmospheric water prior to synthesis, as     we noted after running the reactions with POCl 3 that had been opened and stored for several months. Ray [10] carried out a reaction of water and PCl 5 in dioxane and took extreme care to exclude atmospheric water from the reaction; he reported a yield of 8565% P 18 O 4 . The results obtained using the current procedure resulted in a yield of P 18 O 4 that was equal to or greater than that reported using the more difficult procedure of Ray [10] (Table 3). Similarly, Risley and Van Etten [8] also carried out this reaction, this time excluding atmospheric water using drying tubes, and obtained an overall oxygen-18 enrichment of 90%. This enrichment is 9% less than what would be expected from the reaction as 99 atom % 18 O water was used. Again, the simpler procedure detailed in this study resulted in an improved oxygen-18 enrichment of 97.0%, which represents no loss of enrichment as 97 atom % 18 O water was used in this study.
Natural abundance methods rely on a d 18 O p range of about 10% to 25% between different phosphate sources, which represents a narrow range. Additionally, the d 18 O p ranges of many phosphate sources overlap one another, making it very difficult to infer sources of phosphate. The OLP synthesized from fresh POCl 3 and PCl 5 , on the other hand, had a d 18 O p value around 1,350,000% and 16,120,000%, respectively. This huge separation from other potential phosphate sources should make it possible to differentiate between OLP and other phosphate sources.
Our use of ESI-MS proved to be an effective means to quantify the products of OLP synthesis. ESI-MS analysis provides information about the individual OLP species composition, which sheds light on reaction dynamics that would not be known by simply analyzing an overall O 18 /O 16 ratio. For example, we determined that although the total 18 O composition of our synthesized compounds matched the predicted amount, the 18 O composition of the individual species differed, indicating that the assumptions of either complete, or no P-O bond-breakage in POCl 3 were not met. Bond breakage ranged from 18 to 38%, possibly due to different reaction temperatures during the very violent and exothermic reaction caused by drop wise additions of labeled water.
There have been several previous reports on the stability or decay of OLP in an aqueous solution. Results have ranged from the exchange of oxygen between water and phosphate reaching equilibrium in 3 h [17] to reports of a much slower half-life period of 100 months [12]. The latter result is in closer agreement with more recent publications that state oxygen exchange between phosphate and water under standard environmental conditions does not occur in the absence of biological mediation [15,16]. Our results support the findings of the later studies.
The results from the reactions carried out in ambient atmospheric conditions between POCl 3 or PCl 5 and 97 atom % 18 O water show that over 99% of the OLP molecules contained at     least one oxygen-18 atom, and would therefore be potentially useful for creating and tracing compounds in the laboratory or possibly the environment. Overall, the results indicate that OLP highly enriched in oxygen-18 can be synthesized under ambient atmosphere using a simple procedure and this product does not lose its label over time in the absence of microbial mediation. ESI-MS can be used to easily and effectively gain information about the individual OLP species composition.